Supported Card
|
Solver Description
|
Supported Parameters
|
Notes
|
INITIAL
|
|
|
Defined on the card of the parent system.
|
INJURY
|
|
|
|
OUTPUT_AIRBAG_
CHAMBER
|
Airbag chamber output.
|
AIRBAG_CHAMBER
FE_MODEL
NR_OF_AIRBAG_CHAMBERS
SELECT.HEAT
SELECT.INFLOW
SELECT.INFLOW_PART
SELECT.MASS
SELECT.MASS_FLOW_RATE
SELECT.MASS_INFLOW_RATE_PART
SELECT.MASS_OUTFLOW_RATE_PART
SELECT_MOLAR_FRACTIONS
SELECT.OUTFLOW
SELECT.OUTFLOW_HOLE
SELECT.OUTFLOW_PART
SELECT.OUTFLOW_PERM
SELECT.PRES
SELECT.TEMP
SELECT.TEMP_INFLOW_PART
SELECT.TEMP_OUTFLOW_PART
SELECT.VOLUME
COMMENT
|
|
OUTPUT_ANIMATION
|
Finite element output for animation.
|
PART_LIST
FE_MODEL
SELECT.CONTACT
SELECT.NODE
SELECT.PRES
SELECT.STRAIN
SELECT.STRESS
SELECT.THICK
COMMENT
|
|
ANIMATION_GF
|
|
AIRBAG_CHAMBER_LIST
FE_MODEL
NR_OF_AIRBAG_CHAMBERS
SELECT.COVER
SELECT.DENS
SELECT.MASS
SELECT.PRES
SELECT.TEMP
SELECT.VEL_VECTOR
COMMENT
|
|
OUTPUT_BELT
|
Belt output.
|
INPUT_CLASS (BELT_SEGMENT, BELT_TYING, BELT_RETRACTOR)
INPUT_REF
EXTENDED (OFF/ON)
FILTER (NONE, CFC60, CFC180, CFC600, CFC1000, FIR100)
ASSEMBLY, COMMENT
|
|
OUTPUT_BODY
|
Angular or linear body related output.
|
SIGNAL_TYPE (ANG_VEL, ANG_ACC, LIN_DISP, LIN_POS, LIN_VEL, LIN_ACC)
FILTER (NONE, CFC60, CFC180, CFC600, CFC1000, FIR100)
CRDSYS (REF_SPACE, OBJECT_1, OBJECT_2)
CORRECT AX - AZ (OFF/ON)
ASSEMBLY
define CRDSYS_OBJECT_1.MB or select CRDSYS_OBJECT_1.REF? (OBJECT, REF)
|
|
OUTPUT_BODY_REL
|
Output of a motion quantity of a point on a body relative to a point on another body.
|
SIGNAL_TYPE (REL_DISP, REL_POS, DIST_VEL)
FILTER (NONE, CFC60, CFC180, CFC600, CFC1000, FIR100)
define POINT_OBJECT_1.MB or select POINT_OBJECT_1.REF? (OBJECT, REF)
COMMENT
|
|
OUTPUT_CONTACT
|
Contact output.
|
EXTENDED (OFF/ON)
FILTER (NONE, CFC60, CFC180, CFC600, CFC1000, FIR100)
ASSEMBLY
COMMENT
|
|
OUTPUT_CONTROL_
SYSTEM
|
Output of control system elements.
|
INPUT_CLASS (CONTROLLER, SIGNAL, OPERATOR)
INPUT_REF
FILTER (NONE, CFC60, CFC180, CFC600, CFC1000, FIR100)
COMMENT
|
|
OUTPUT_CROSS_
SECTION
|
Defines a plane for which cross sectional forces and moments are outputted.
|
POS (X, Y, Z)
NORMAL_DIR (X, Y, Z)
EDGE_DIR (X, Y, Z)
LENGTH_L , LENGTH_M, FILTER (NONE, CFC60, CFC180, CFC600, CFC1000, FIR100)
FE_MODEL
|
|
OUTPUT_ELEMENT
|
Element output.
|
INT_POINT_LIST
FILTER (NONE, CFC60, CFC180, CFC600, CFC1000, FIR100)
FE_MODEL
NR_OF_INT_POINTS
SELECT.PROPERTY
SELECT.PRES_EXTERNAL
SELECT.STRESS
SELECT.STRAIN
SELECT.STRESS_TRUSS2
SELECT.STRAIN_TRUSS2
SELECT.STRESS_BEAM2
SELECT.STRAIN_BEAM2
SELECT.STRESS_INTERFACE
SELECT.STRAIN_INTERFACE
COMMENT
|
|
OUTPUT_ELEMENT_
INITIAL
|
Element output of initial state.
|
SELECT_FRAME (OFF/ON)
SELECT_LUMP (OFF/ON)
FE_MODEL
COMMENT
|
|
OUTPUT_ENERGY_FE_
MODEL
|
Energy output of the FE models or its parts.
|
FE_MODEL_LIST
SUM_FE_MODEL (OFF/ON)
ENERGY_ALL (OFF/ON)
KINETIC (OFF/ON)
DISSIPATION (OFF/ON)
DISSIPATION_IMM (OFF/ON)
DISSIPATION_MATERIAL (OFF/ON)
DISSIPATION_PLASTIC (OFF/ON)
DISSIPATION_RAYLEIGH (OFF/ON)
INTERNAL (OFF/ON)
INTERNAL_PLASTIC (OFF/ON)
INTERNAL_HOURGLASS (OFF/ON)
INTERNAL_IMM (OFF/ON)
EXTERNAL (OFF/ON)
EXTERNAL_CONTACT (OFF/ON)
EXTERNAL_FORCES (OFF/ON)
FE_PART (OFF/ON)
TOTAL (OFF/ON)
BALANCE (OFF/ON)
MASS_SCALING (OFF/ON)
FILTER (NONE, CFC60, CFC180, CFC600, CFC1000, FIR100)
NR_OF_FE_MODELS
COMMENT
|
|
OUTPUT_JET
|
Output of jet related properties.
|
JET_LIST
FE_MODEL
NR_OF_JETS
SELECT.FORCE_RES
COMMENT
|
|
OUTPUT_JOINT_
CONSTRAINT
|
Joint constraint force or torque output.
|
JOINT
SIGNAL_TYPE (FORCE, TORQUE)
FILTER (NONE, CFC60, CFC180, CFC600, CFC1000, FIR100)
ASSEMBLY
COMMENT
|
|
OUTPUT_JOINT_DOF
|
Joint position, velocity or acceleration degrees of freedom (DOF) output.
|
JOINT
SIGNAL_TYPE (POS, VEL, ACC)
ASSEMBLY
COMMENT
|
|
OUTPUT_MARKER
|
Marker output for animation.
|
ASSEMBLY
define CRDSYS_OBJECT_1.MB or select CRDSYS_OBJECT_1.REF (OBJECT, REF)
COMMENT
|
|
OUTPUT_MOTION_
STRUCT
|
Data for creating a structural motion output file.
|
MOTION_TYPE (DISP, VEL)
FILE
FE_MODEL
COMMENT
|
|
OUTPUT_MUSCLE
|
|
ASSEMBLY
COMMENT
|
|
OUTPUT_NODE
|
Nodal output.
|
FE_MODEL
SELECT.POS
SELECT.DISP
SELECT.ROT
SELECT.VEL
SELECT.ACC
SELECT.FORCE
SELECT.FORCE_INTERNAL
SELECT.FORCE_EXTERNAL
SELECT.FORCE_REAC
SELECT.MOMENT_REAC
COMMENT
|
|
OUTPUT_NODE_INITIAL
|
Nodal output of initial state.
|
SELECT_POS (OFF/ON)
SELECT_VEL (OFF/ON)
SELECT_ACC (OFF/ON)
SELECT_MASS (OFF/ON)
FE_MODEL
COMMENT
|
|
OUTPUT_RESTRAINT
|
Restraint output.
|
EXTENDED (OFF/ON)
FILTER (NONE, CFC60, CFC180, CFC600, CFC1000, FIR100)
ASSEMBLY
COMMENT
|
|
OUTPUT_SENSOR
|
Sensor signal output.
|
SENSOR
ASSEMBLY
COMMENT
|
|
OUTPUT.STRAP
|
|
FE_MODEL
SELECT.FORCES_RES
SELECT.ELONG
SELECT.PROPERTY
COMMENT
|
|
OUTPUT_SYSTEM_COG
|
Position, velocity and acceleration output of the combined center of gravity of the selected system(s).
|
WRITE_ALL
WRITE_POS
WRITE_VEL
WRITE_ACC
FILTER (NONE, CFC60, CFC180, CFC600, CFC1000, FIR100)
ASSEMBLY
COMMENT
|
|
SELECT
|
|
|
Defined on the card of the parent element.
|
SURFACE.PLANE
|
Rectangular plane
|
multibody = BODY
N1 = POINT_1
N2 = POINT_2
N3 = POINT_3
|
To create a SURFACE under the SYSTEM.REF_SPACE, a reference to a null body must be selected because HyperMesh requires a reference to a multibody when creating a multibody plane. A null body can be created like any other BODY (card image is not relevant and should not be used), Nullbody should be put under the SYSTEM.REF_SPACE assembly.
|